|
Dial-up / FAQ / PPP for Windows 98 (English edition)
НАСТРОЙКА ПОДКЛЮЧЕНИЯ К СЕТИ ИНТЕРНЕТ ДЛЯ WINDOWS 98 (на английском языке)
(Инструкцию для распечатки в формате PDF можно скачать здесь.)
MAKING A NEW DIAL UP CONNECTION FOR SPbGU
In order to make a new dial up connection double click My Computer and then Dial-Up Networking (Picture.1).
Inside that window you will find the Make New Connection icon which will guide you through the rest of the
connection creation process.
Pic. 1
Double click the Make New Connection icon. This will start the following dialog window (Picture. 2).
Pic. 2
Here you must enter the new Dial-Up connection name (SPbGU in this case) and select the modem that is
connected to your computer. Then click Next (Picture. 3).
Pic. 3
This dialog window allows you to select the area code and country code and also the telephone number that you
will use to connect to SPbGU. When done, click Next and you will see the following window (Picture. 4).
Pic. 4
Click Finish. The new connection appears in the Dial-Up Networking window (Picture. 5).
Pic. 5
SETTING UP THE DIAL-UP CONNECTION
The Dial-Up connection you just created must have the correct properties set in order to connect to SPbGU. Right
click on SPbGU icon you just made and click Properties (Picture. 6), (Picture. 7).
Pic. 6
Pic. 7
The General tab (Picture.7) shows the most important settings, such as the phone number, the area and country
code and the modem that you use. Click Configure button. You will see the modem properties window (Picture.8)
Pic. 8
Select the Options tab (Picture. 9)
Pic. 9
ATTENTION! Make sure there is a check in the box next to "Bring up terminal window after dialing".
There should be no check before "Bring up terminal window before dialing". Click on Ok, to go back to
the General tab and then click on Server Types (Picture. 10).
Pic. 10
At the Type of Dial-Up Server select (PPP: Internet, Windows NT Server, Windows 98). At the Advanced options
mark Enable software compression And at the Allowed network protocols mark the TCP/IP protocol. Click on
TCP/IP Settings button (Picture.11)
Pic. 11
Select Server assigned IP address and Specify name server addresses.
As a primary DNS type 193.124.85.219 and as a Secondary DNS type 193.124.85.210
Use IP header compression and Use default gateway on remote network must both be marked.
Now close all windows by pressing Ok and you can try to get connected.
If you clicked the Bring up terminal window after dialing check box is the previous section, a terminal window
appears in which you type your logon information. After you type your user name and password, click Continue.
The order in which you log on and the information that you have to provide may vary, depending on your ISP.
Contact your ISP if you have any questions about the logon procedure.
MAKING A CONNECTION TO SPbGU
The following explains how to connect to SPbGU. These steps will need to be followed whenever you want
to browse the WWW, or access any other internet resource.
1. Double click on the My Computer icon, located on the Desktop.
2. The drives and three folders should be seen -- Control Panel, Printers, and
Dial-Up Networking.
3. Double click on Dial-Up Networking.
4. A window with at least two icons will be displayed -- Make New Connection and the connection you made in the
previous section. (The user in our example named the icon SPbGU. We will refer to the created icon as SPbGU for
the remainder of these instructions.) Double click on SPbGU.
5. A dialog box will appear (Picture. 12). Click Connect.
Pic. 12
NOTE: The Username and Password fields must be left blank!
6. A dialog box will appear stating that Windows 98 is using the modem and dialing 326-4911. This will take
approximately 30 seconds. When the connection is made, a Post Dial Terminal Screen will appear (Picture. 13).
Type in your Username (pp**** see in User card) and press Enter.
Pic. 13
Then, type your Password (****** see in User card) and press Enter.
Pic. 14
You will see a data stream consisting of "garbage", or ASCII, characters (Picture. 14). This is nothing to worry
about. It indicates that your modem and our modem bank are communicating correctly. When you see these
characters press F7, or click the Continue (F7) button, at the bottom of the window.
At this point you are ready to use any Internet Winsock Compliant application you wish, including Internet Explorer,
Netscape, Telnet and FTP.
When you are finished, double click on the small green icon, and then click the Disconnect on the Connection
Uptime dialog box. This will hang up the modem and disconnect you from SPbGU.
Назад к списку FAQ
|
WELCOME
